Click to enlarge
Optical Fibre Distribution Frame (FDF) (Model No. : RI-110)
Optical Fibre Distribution Frame (FDF) (Model No. : RI-110)
Back to products
Suspension Fitting Assembly (Helix Type-I)
Suspension Fitting Assembly (Helix Type-I)

Dead End & Termination Fittings (Helix Type-I)

Product Overview

Dead End & Termination Fittings are designed for dead-ending aerial ADSS cables on access networks & are installed on the Tension or Terminating poles where splices are located or at the poles where the overhead alignment takes a turn of angle exceeding more than 15°. Span length between Tension poles does not exceed more than 75m. These fittings relieve the optical fiber cable of its compressive, bending & clamping stresses.

Category:
Description

Applications

These are used as cable dead-end at tension poles where splices are located and at poles where the overhead alignment takes a turn angle exceedingly 15°. Suitable for cables with 8-18 mm diameter where tensile strength is more than 10 kN.

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Dead End & Termination Fittings (Helix Type-I)”

Your email address will not be published. Required fields are marked *

Related products

Anchoring / Tensioning Clamp assembly (Edge Type)

Applications Anchoring assemblies shall be used to firmly hold ADSS cable to a concrete, wood or steel pole and transmit the mechanical tension at the end of a run, tensioning points and a major change in direction of over 20 degrees.  

Suspension Fitting Assembly (Helix Type-II)

Product Overview Suspension Fitting Assembly shall be used for holding the aerial Optical Fiber Cable against the dynamic stress of Aeolian vibration at the suspension points. These types of fittings shall be installed at all the intermediate poles between tension poles. This type of fitting also reduces static stresses at the support point.

Suspension Clamp Assembly ((Drop Fibre Accessories)

Applications Suspension Drop Fiber Assembly shall be used for holding the aerial ADSS & OPGW cable at an intermediate point of support such as pole/ cross arm/ wall with the help of SS Strap or nuts and bolts when the cable route deviates up to 20°. It is specially designed for Cable dia between 5-8mm and 2-4 Fiber cables.

Adjustable Cable Storage Bracket

Applications Adjustable Cable Storage Bracket Assembly is used to store the excess ADSS & OPGW cable which is being maintained in the middle of the line on the poles or cross arms & to use at the time of joints. SS Strip: SS Strap with casing is supplied in 50m roll with indication of remaining length. SS Strap with Buckle shall be used for mounting the bracket on the pole as per load requirement. Minimum two loops of 0.75 meter each with one Buckle shall be considered for attaching the brackets to the poles.

Down Lead Clamp (Edge Type)

Applications Down Lead Clamp is used to properly fix the aerial ADSS cable on the pole or cross arms to avoid the movement of the cable under wind condition. The Down Lead Clamp has the provision to fix it on the pole or cross arms by Stainless Steel Straps & Buckles.

Suspension Fitting Assembly (Helix Type-I)

Product Overview Suspension Fitting Assembly shall be used for holding the aerial Optical Fiber Cable against the dynamic stress of Aeolian vibration at the suspension points. These types of fittings shall be installed at all the intermediate poles between tension poles. This type of fitting also reduces static stresses at the support point.

Pole Clamp/Universal Pole Clamp

Applications Pole clamp is a key product in the whole Cable laying accessories set as it acts as the sole connector between pole & all the other accessories being installed. Design of pole clamp can vary from pole to pole. Riddhi Infratel has also • developed a Universal Pole Clamp which can be installed on any pole, irrespective of size and shape with the help of SS Strap and Buckle.

Dead End & Termination Fittings (Helix Type-II)

Product Overview Dead End & Termination Fittings are designed for dead-ending aerial ADSS cables on access networks & are installed on the Tension or Terminating poles where splices are located or at the poles where the overhead alignment takes a turn of angle exceeding more than 15°. Span length between Tension poles does not exceed more than 90 meter. These fittings relieve the optical fiber cable of its compressive, bending & clamping stresses.