Showing 1–12 of 15 results

Show sidebar
Show 9 12 18 24

Adjustable Cable Storage Bracket

Applications Adjustable Cable Storage Bracket Assembly is used to store the excess ADSS & OPGW cable which is being maintained in the middle of the line on the poles or cross arms & to use at the time of joints. SS Strip: SS Strap with casing is supplied in 50m roll with indication of remaining length. SS Strap with Buckle shall be used for mounting the bracket on the pole as per load requirement. Minimum two loops of 0.75 meter each with one Buckle shall be considered for attaching the brackets to the poles.

Anchoring / Tensioning Clamp assembly (Edge Type)

Applications Anchoring assemblies shall be used to firmly hold ADSS cable to a concrete, wood or steel pole and transmit the mechanical tension at the end of a run, tensioning points and a major change in direction of over 20 degrees.  

Cable Storage Bracket Assembly (Helix Type-II)

Product Overview Cable Storage Bracket Assembly shall be used for storing Optical Fiber Cable for future repair & maintenance which has to be carried out at regular intervals & to be installed at terminating points if required. This Bracket is made up of Hot Dip Galvanized steel will serve the purpose on both the pole to pole & pole to wall spans.

Dead End & Termination Fittings (Helix Type-I)

Product Overview Dead End & Termination Fittings are designed for dead-ending aerial ADSS cables on access networks & are installed on the Tension or Terminating poles where splices are located or at the poles where the overhead alignment takes a turn of angle exceeding more than 15°. Span length between Tension poles does not exceed more than 75m. These fittings relieve the optical fiber cable of its compressive, bending & clamping stresses.

Dead End & Termination Fittings (Helix Type-II)

Product Overview Dead End & Termination Fittings are designed for dead-ending aerial ADSS cables on access networks & are installed on the Tension or Terminating poles where splices are located or at the poles where the overhead alignment takes a turn of angle exceeding more than 15°. Span length between Tension poles does not exceed more than 90 meter. These fittings relieve the optical fiber cable of its compressive, bending & clamping stresses.

Demountable Pulleys (Helix Type-I)

Product Overview Demountable Pulleys are used during the installation of Aerial Optical Fiber Cables. These are made from Mild Steel & the contour of the wheel is coated with rubber or any other suitable material for free movement of the Aerial Optical Fiber Cable.

Down Lead Clamp (Edge Type)

Applications Down Lead Clamp is used to properly fix the aerial ADSS cable on the pole or cross arms to avoid the movement of the cable under wind condition. The Down Lead Clamp has the provision to fix it on the pole or cross arms by Stainless Steel Straps & Buckles.

Pole Clamp/Universal Pole Clamp

Applications Pole clamp is a key product in the whole Cable laying accessories set as it acts as the sole connector between pole & all the other accessories being installed. Design of pole clamp can vary from pole to pole. Riddhi Infratel has also • developed a Universal Pole Clamp which can be installed on any pole, irrespective of size and shape with the help of SS Strap and Buckle.

SS Strap & Buckle

Applications SS Strap & Buckle is a specially designed & developed product to provide ease in installation of accessories. This tool helps in holding & binding the accessories which are being mounted on the pole. This tool is designed to keep ease in use & provide strength to the network.

Strap Binding Cutting Tool

Applications Strap Binding Cutting Tool is a specially designed & developed to provide ease in installation of accessories. This tool helps in cutting & binding the SS strap along the pole for gripping the accessories being mounted on pole. This tool is designed to keep ease in use & improve efficiency in installation of accessories.

Suspension Clamp Assembly ((Drop Fibre Accessories)

Applications Suspension Drop Fiber Assembly shall be used for holding the aerial ADSS & OPGW cable at an intermediate point of support such as pole/ cross arm/ wall with the help of SS Strap or nuts and bolts when the cable route deviates up to 20°. It is specially designed for Cable dia between 5-8mm and 2-4 Fiber cables.

Suspension ClampAssembly (Edge Type)

Applications Suspension Clamp Assembly shall be used for holding the aerial ADSS & OPGW cable at an intermediate point of support such as pole or cross arm when the cable route deviates up to 20°. It is specially designed keeping in mind the issue of installation. It can be mounted by both SS Strap & Buckle or Nuts & bolts.