Click to enlarge
Optical Fibre Distribution Frame (FDF) (Model No. : RI-110)
Optical Fibre Distribution Frame (FDF) (Model No. : RI-110)
Back to products
Suspension Fitting Assembly (Helix Type-I)
Suspension Fitting Assembly (Helix Type-I)

Dead End & Termination Fittings (Helix Type-I)

Product Overview

Dead End & Termination Fittings are designed for dead-ending aerial ADSS cables on access networks & are installed on the Tension or Terminating poles where splices are located or at the poles where the overhead alignment takes a turn of angle exceeding more than 15°. Span length between Tension poles does not exceed more than 75m. These fittings relieve the optical fiber cable of its compressive, bending & clamping stresses.

Category:
Description

Applications

These are used as cable dead-end at tension poles where splices are located and at poles where the overhead alignment takes a turn angle exceedingly 15°. Suitable for cables with 8-18 mm diameter where tensile strength is more than 10 kN.

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Dead End & Termination Fittings (Helix Type-I)”

Your email address will not be published. Required fields are marked *

Related products

Adjustable Cable Storage Bracket

Applications Adjustable Cable Storage Bracket Assembly is used to store the excess ADSS & OPGW cable which is being maintained in the middle of the line on the poles or cross arms & to use at the time of joints. SS Strip: SS Strap with casing is supplied in 50m roll with indication of remaining length. SS Strap with Buckle shall be used for mounting the bracket on the pole as per load requirement. Minimum two loops of 0.75 meter each with one Buckle shall be considered for attaching the brackets to the poles.

Anchoring / Tensioning Clamp assembly (Edge Type)

Applications Anchoring assemblies shall be used to firmly hold ADSS cable to a concrete, wood or steel pole and transmit the mechanical tension at the end of a run, tensioning points and a major change in direction of over 20 degrees.  

Tension Clamp Assembly (Drop Fibre Accessories)

Applications Tension Drop Fiber assemblies are used to firmly hold ADSS cable to a concrete, wood or steel pole and transmit the mechanical tension throughout the cable length. The tension drop Fiber assembly is mounted in a set of two tension drop Fiber fixtures with a pole clamp

Strap Binding Cutting Tool

Applications Strap Binding Cutting Tool is a specially designed & developed to provide ease in installation of accessories. This tool helps in cutting & binding the SS strap along the pole for gripping the accessories being mounted on pole. This tool is designed to keep ease in use & improve efficiency in installation of accessories.

Suspension Clamp Assembly ((Drop Fibre Accessories)

Applications Suspension Drop Fiber Assembly shall be used for holding the aerial ADSS & OPGW cable at an intermediate point of support such as pole/ cross arm/ wall with the help of SS Strap or nuts and bolts when the cable route deviates up to 20°. It is specially designed for Cable dia between 5-8mm and 2-4 Fiber cables.

Down Lead Clamp (Edge Type)

Applications Down Lead Clamp is used to properly fix the aerial ADSS cable on the pole or cross arms to avoid the movement of the cable under wind condition. The Down Lead Clamp has the provision to fix it on the pole or cross arms by Stainless Steel Straps & Buckles.

Cable Storage Bracket Assembly (Helix Type-II)

Product Overview Cable Storage Bracket Assembly shall be used for storing Optical Fiber Cable for future repair & maintenance which has to be carried out at regular intervals & to be installed at terminating points if required. This Bracket is made up of Hot Dip Galvanized steel will serve the purpose on both the pole to pole & pole to wall spans.

SS Strap & Buckle

Applications SS Strap & Buckle is a specially designed & developed product to provide ease in installation of accessories. This tool helps in holding & binding the accessories which are being mounted on the pole. This tool is designed to keep ease in use & provide strength to the network.